Digitizing negatives using the Reprostativ, a lightbox and a camera

Inspired by numerous success stories of people digitizing negatives with their digital cameras, while often obtaining better results than their scanners, I decided to give it a go myself. Here, I’ll use a Pentax K20D, a Kaiser slimlite piano lightbox, a Digitaliza film holder and the Reprostativ to digitize 120 negatives. While this is mainly to explain the setup and workflow I’m using, I’ll briefly compare the process and results to the Epson v550 scanner I’ve used so far.

The Reprostativ copy stand

The Reprostativ V5 kit, as designed by Jochen Möller and sold by Dold Mechatronik.

In order to keep everything aligned properly, you’ll need something that resembles a copy stand. Some people have success with using a tripod mounted in reverse, however there are two problems with this approach: 1) you have to carefully align the legs and 2) you can’t keep it as a permanent setup on your desk. The Reprostativ V5 kit solves this problem. It is a kit which contains all the parts to make your own copy stand (except for the quick release plate and some felt pads to put underneath the arms, as stated in the manual).

The Reprostativ is sold by a German company and as such, the manual is also written in German. However, even if you don’t speak German, it should be easy to follow because of the very clear pictures. The end product feels very solid and sturdy. The only thing that was strange, is that the plastic end caps have to be forced into the openings, essentially removing part of the plastic in the process. However, once they are in (use a hammer) they are locked tight.

To complete the copy stand, you need a tripod quick release to hold the camera in place. Any Arca-Swiss compatible release plate will do, however the manufacturer recommends the Andoer DM-55 Clamp and Quick Release Plate which I have also used here. You attach the plate in the approximate position that is needed to get a sharp image of the negative. Then, you can fine-tune the position of the camera by slightly loosening the clamp and moving the camera up and down. Although a more elaborate system is probably even more convenient, after some practice it is actually quite a fast way to focus on the negative. And if you want to photograph a series of negatives using the same magnification, you only have to set it once and make micro-adjustments using the QR plate when necessary.

The light source

The second important part is the light source. The best advice on this front that I have found, was the very detailed post written by Nate over at the Negative Lab Pro forums. To restate his main points: 1) you want a high color rendering index (CRI), 2) good separation of color channels in spectral sensitivity curves, 3) an even illumination and finally 4) consider how “collimated” or diffused the light source is in your setup. Based on his recommendations, I went for the “Kaiser Slimlite Plano (CRI = 95, very even)” but I recommend you read the original post and the discussion over at the forum thread. The nice thing is that the Slimlite panel I’ve bought (29×20 cm) precisely fits on the legs of the Reprostativ.

The film holder

For a film holder, you can use anything that keeps your negatives flat and far away enough from the light source to prevent both Newton’s rings (where the film comes in contact with a smooth surface) and ensure an even lighting. I’ve used the Digitaliza 120 film holder because it is sturdy and I already had one available.

Optics: the lens and camera

The final but also very important part of the setup is the device that actually captures the information: the digital camera (with the appropriate lens). I have used a Pentax K20D (14.6 megapixel) but of course the higher resolution and the larger your sensor is, the better the final result is (potentially).

For 120 format negatives, a 50mm lens works nicely. You want to use a macro lens (or an enlarger lens) because these are (generally) sharp across the whole image plane. In my setup, I use a Pentax K mount Sigma 50mm 1:2.8 DG Macro, which can reach a 1:1 reproduction ratio. To fill the sensor with a 120 negative on my Pentax K20D, I use a reproduction ratio of roughly 1:4, if you want to make multiple captures and stitch them (more on that later), you can use something like 1:1.5 for approximately four captures (including some overlap) or you can go all the way up to 1:1 to extract the most detail.

The results at a 1:1 magnification from this simple setup are quite stunning – they blow the Epson v550 out of the water!

My setup and first results

Now we have discussed all the parts that are needed to digitize negatives using your digital camera, I’ll show you my workflow! On the right you can see the actual setup, which fits nicely on my (somewhat messy) desk. The Pentax K20D is tethered to my PC via a USB cable so that I can conveniently control the camera from my laptop with the open-source program pkTriggerCord. Then, I edit the RAW files in RawTherapee and make some final adjustments in Gimp. When using a 1:4 magnification (so that the whole 120 negative fills the frame) this whole process takes only a few minutes. Dust is of course always a problem: however, just before shooting the image, you can use a Rocket air blower to remove dust at the last minute.

My setup in action: scanning a 120 negative at a 1:1 reproduction ratio.
Comparison between a cropped scan from the Epson and the camera setup at 1:1 magnification. The Epson scan was 129% resized and the camera scan 78% resized so the images have the same number of pixels.

Before the camera scanning setup, I was using a trusty Epson v550 to scan my negatives. However, I could never quite get along with it. The scanner is quite a dust magnet and the holders that come with it are quite flimsy (hence I bought the Digitaliza holder). Additionally, while there is a Linux driver for the Epson v550 available, it never played nice in my experience: sometimes the scanner was only recognized when plugged into a certain USB port and sometimes not at all. The automatic cropping of the 120 negatives never properly worked and the whole process felt slow.

Also, I had the feeling I could never get scans that were quite sharp. Enter the comparison image on the left: the same negative scanned on the Epson using the best settings I’ve found and using the camera setup (at 1:1 magnification). To me, the results from the camera are spectacular: they are decidedly sharper than the scanner results.

Perhaps the same result could be obtained by carefully tweaking the height of the film holder on the scanner, but focusing using the camera setup is much easier in my opinion. Additionally, the camera image was scaled down and the scanner image was scaled up to have the same number of pixels for the comparison, so in reality the camera images can have a much higher resolution than the Epson scans, which enables larger or more detailed digital prints, or pleasing digital crops.

Caveats or where to go next

There are a few things to note about the setup: first, the comparison above was done at a 1:1 magnification. This implies that for a single negative, you have to take multiple shots and stitch them together afterwards. This is something I have not tested yet, but plan to try soon. However, looking at the image below, there is not much difference in quality when taking just a single shot at 1:4 or using the Epson scanner for sharing photos online. But to me, the process is much more enjoyable and also a lot quicker.

Comparison of the highest quality setting of the Epson to a “one shot” capture with the Pentax at 1:4 magnification shows little difference when scaled down for web viewing.

Additionally, a setup that uses a camera for digitizing negatives offers numerous other possibilities that are not always possible with a scanner. For example, when using 35mm negatives, one could include the sprocket holes and more generally, larger (panoramic) formats can be digitized by stitching multiple shots. Stitching is something I’ll try next, as well as color negatives and the combination of shots of different exposure times to increase the dynamic range that can be extracted from the negative (à la HDR). Any feedback or tips are very much appreciated!

I hope you enjoyed this article. It contains Amazon affiliate links to the products I’ve discussed, if you decide to purchase any of them, a small portion of the proceedings will help to support this blog.